Hey everyone, it’s Jake here, and I’ve been working as an air cooler tube bundle supplier for almost a decade now. Over those years, I’ve seen firsthand how the right coating can make or break a tube bundle’s lifespan—especially in harsh industrial environments. A lot of folks reach out to me asking, “What’s the actual process to apply a coating to these bundles?” instead of just buying a pre-coated unit, so I figured I’d break it down step-by-step, with the lessons I’ve learned from helping refineries, petrochemical plants, and power stations get their tube bundles ready for tough conditions. First, a quick note: the coating process changes a bit depending on if you’re working with stainless steel or carbon steel bundles. If you’re still deciding which material is right for your setup, we’ve got both options—check out our Stainless Steel Air-cooled Tube Bundle for corrosion-heavy spots or Carbon Steel Air-cooled Tube Bundle for standard, less corrosive environments. Let’s dive in.
First up, prep work—this is the part most people skip or rush, and that’s where things go wrong. I can’t tell you how many times a plant will bring a bundle to us with loose rust, oil, or even just dust caked on, and we have to send it back because the coating won’t adhere properly. Think of coating like painting a wall: if you don’t sand off old paint and wipe away grease, the new stuff will peel in a few months, not years. For tube bundles, the prep has to be consistent across every inch of the tubes, because even a tiny pinhole of un-prepped metal will become a rust spot fast.
Step one in prep is surface cleaning. Most industrial bundles come with a thin layer of mill scale (the flaky stuff that forms when metal is heated during manufacturing) right out of the factory. For carbon steel bundles, that mill scale has to go first—we use a combination of alkaline cleaning and mechanical cleaning here, not just pressure washing. Alkaline cleaning uses a mild, water-based solution to cut through oil, grease, and organic contaminants that got on the bundle during shipping. We soak the bundle in a heated alkaline tank for 30 to 45 minutes, then rinse it with high-pressure hot water to get rid of all the gunk. If we skip that, the sandblasting we do next won’t work as well—grease under the sandblasted surface will make the coating lift.
Once the alkaline rinse is done, it’s time for surface profiling, which is just a fancy way of saying sandblasting to create a rough, textured surface. For stainless steel bundles, we use a different abrasive than carbon steel—we go with steel grit for carbon steel and stainless steel grit for stainless steel, because using the wrong abrasive can cause cross-contamination (like iron particles sticking to stainless steel, leading to rust later). The goal here is a profile of around 2.5 to 5 mils—too rough, and the coating traps air and debris; too smooth, and it won’t stick. We also do a visual check after sandblasting: the entire surface has to be a uniform gray (for carbon steel) or metallic silver (for stainless steel) with no shiny patches, mill scale, or leftover grease. If there’s any shine, we missed a spot and have to blast it again.
Wait, one quick tip from experience: always do the sandblasting on-site if possible, or at least inspect the bundle immediately after it gets to your shop. We once had a customer send a carbon steel bundle that was fine when it left their plant, but by the time it got to us (a 3-day truck ride), it had rusted a little on the ends that were exposed. We had to re-blast those ends, and it pushed their project timeline back a week—they were not happy. So if you’re prepping a bundle yourself, don’t leave it sitting around after the first cleaning.
Next, after prep, we move on to the coating application itself. This is where the material matters most, like I mentioned earlier. For carbon steel bundles, which are prone to rust in humid or chemical-heavy areas, we use a two-part epoxy primer first, then a polyurethane topcoat. For stainless steel, we use a silicone-based coating because it’s more resistant to high temperatures (stainless steel bundles are often used in areas with higher heat, like power plant condensers) and doesn’t flake as easily under thermal cycling. But let’s talk about the application process, not just the coating type.
The main application method we use is airless spraying, and it’s non-negotiable for us. Rollers or brushes work okay for small parts, but airless spraying gets into every nook and cranny of the tube bundle—like the gaps between the tubes, the header ends, and the thin fins (wait, right, most air cooler tube bundles have those aluminum fins attached to the tubes to boost heat transfer—those tiny fins are easy to miss with a brush). Airless spraying uses high pressure to push the coating through a tiny nozzle, creating a fine mist that covers every surface evenly. We set the pressure between 2,000 and 3,000 PSI, which is strong enough to get into the fin gaps but not so strong that it blows the coating off.
For the first coat (the primer), we always apply it within 4 hours of sandblasting the bundle. That’s another key point—metal that’s been blasted is super reactive to oxygen, so if you wait too long, it will start to flash rust (a thin layer of rust that forms fast) before you can coat it. Flash rust is way harder to cover than regular rust, and it will ruin the coating’s adhesion. We once learned this the hard way: we had a big carbon steel bundle that got held up in our shop for a day because of a scheduling mix-up. By the time we tried to prime it, there was a light layer of flash rust all over the tubes. We tried sanding it off, but it was too fine—we ended up re-blasting the whole thing, which cost us extra time and material, and made our customer late on their project. Now we have a strict rule: no waiting longer than 4 hours post-blast for primer.


Once the primer is on, it needs to cure before we apply the topcoat. Curing time depends on the temperature and humidity—we follow the coating manufacturer’s specs, but I’ve found that in 70°F (21°C) weather with 50% humidity, the primer is ready for topcoat in about 12 hours. If it’s hotter or more humid, it cures faster; if it’s cold or damp, we use a space heater to warm up the shop (not direct heat on the bundle) to speed things up. We test the primer’s cure by touching it gently—if it doesn’t smudge and feels hard, it’s ready. If it’s still tacky, the topcoat will mix with the primer and cause a sticky, uneven finish.
For the topcoat, we do two coats, just like the primer—wait, no, actually three coats total? Let me count: primer is coat 1, then mid-coat, then topcoat? No, for our standard process, it’s primer (1), intermediate coat (2), and finish coat (3). The intermediate coat adds extra thickness and protection, which is important for areas where the bundle will be exposed to abrasion, like if it’s in a plant where heavy equipment moves nearby. The finish coat is the one that gives the bundle its color (usually light gray or white, which helps reflect heat, a bonus for air coolers) and adds the final layer of corrosion resistance.
A lot of people ask if they can dip the bundle in a coating tank instead of spraying. We tried that a few years ago for small bundles, but it’s not worth it for most cases. Dipping can leave drips on the header ends, and it’s hard to control the thickness—too thin, and you get bare spots; too thick, and the fins clog up with coating, which kills the heat transfer. Spraying lets us target exactly where the coating needs to be, and we can adjust the thickness as needed. We do use dipping for some small parts, like bolted connections, but never for the main tube bundle tubes or fins.
After application, curing is the final step before the bundle is ready to install. This isn’t just letting it dry—we have to let the coating cure fully, not just “dry to the touch.” For our epoxy/polyurethane system on carbon steel, that’s 7 days at room temperature. For silicone coatings on stainless steel, it’s 10 days, because silicone cures more slowly. We keep the bundle in our controlled-temperature shop during this time, away from dust and moisture—even a light rain or a dusty workbench can ruin the finish. Once it’s fully cured, we do a quick inspection: run a magnetic thickness gauge over the tubes to make sure the coating is between 5 and 10 mils thick (we spec 8 mils for most bundles), check for any missed spots, and do a salt spray test for corrosion resistance. If it passes, it’s ready to go to the site.
Wait, I should also mention common mistakes people make when they do this themselves, not when we do it. A lot of plant maintenance teams will try to recoat a tube bundle that’s already in service, right? That’s a whole different process. If you’re recoating an existing bundle, you have to first remove all the old coating, which is way more work than prepping a new bundle. You can’t just sand over old coating—you have to strip it with a chemical stripper or blast it, same as new prep. Also, if the old bundle has rust pitting (those small holes in the metal), you have to grind those out before coating, otherwise the pit will fill with air and cause the coating to crack.
Another thing: thermal expansion. Air cooler tube bundles go through a lot of temperature changes—they’re hot when the plant is running, cold when it’s shut down. The coating has to expand and contract with the metal, otherwise it will crack. That’s why we use flexible coatings for high-temperature applications, not rigid ones. We once used a rigid epoxy on a bundle in a refinery that ran at 350°F, and after 6 months, the coating cracked all over because it couldn’t handle the thermal cycling. Now we switch to a flexible epoxy that has more elasticity for those high-heat spots.
If you’re reading this and wondering if coating your air cooler tube bundle is worth it—let me save you the math. A coated bundle will last 10 to 15 years, vs. 3 to 5 years for an uncoated one, especially in corrosive environments. I had a customer last year in the Gulf Coast, where salt air is brutal, who didn’t coat their original bundle and had to replace it every 4 years. They switched to our pre-coated stainless steel bundles (check out that link if you’re interested) and they’re still running strong after 8 years. For a carbon steel bundle in a milder area, coating adds another 5 to 7 years of life, which pays for the coating cost in no time.
Now, if you’re not sure whether to coat a new bundle, or you need help with a recoating project, feel free to reach out to our team. We work with all kinds of industrial clients, big and small, and we can walk you through every step—from material selection to application, whether you do it yourself or have us do it. Don’t wait until your bundle starts rusting to take action; a little prep and coating now will save you thousands in replacements and downtime later.
References:
- Air Pollution Control Association. (2018). Industrial Coating Applications for Heat Exchangers and Air Coolers.
- NACE International. (2020). Surface Preparation and Coating Specification for Metal Substrates.
- ASME. (2019). Standards for Air Cooler Tube Bundle Design and Maintenance.
- The Aluminum Association. (2021). Coating Compatibility with Finned Heat Transfer Surfaces.
- Heat Exchange Institute. (2022). Guide to Extending Air Cooler Tube Bundle Lifespan.
